October 03, 2008

CP Automation set to integrate new resistor ranges

Service and supply of drives, VSDs, Inverters, controls and braking resistors~ Service and maintenance specialist increases its focus on the elevation, crane and OCH sectors ~

Service and maintenance specialist CP Automation has announced that it will be improving its product offering for the elevation, crane and OCH industries by adding Cressall Resistor’s HP and ES series braking resistors to its portfolio. The relationship with Cressall is now well established and compliments CP Automation’s range of independent supply relationships with manufacturers of inverters, PLCs and other electronic equipment and control systems.

First in CP Automation’s range is Cressall Resistors’ HP series of high performance dynamic braking resistors (DBRs). The new range is ideal for use on cranes, winches, conveyors and test loads as well as on lifts and elevators. These compact, ready boxed DBRs are enclosed to IP20 and make virtually no noise when subject to inverter braking currents. Their low inductance open-wound element construction allows high power-dissipation in a small space. It is these two factors that make the HP series ideal for use in lifts and elevators where noise and heat dissipation are both significant issues. When used with an inverter, the units are suitable for use with any make of drive.

The range is divided into HP1, HP2 and HP3 units, which have continuous power ratings of 1.5kW, 3.0kW and 4.5kW respectively. The continuous power ratings can be exceeded when power is applied for less than 100% of the time and the extent to which this can be done is calculated using a simple equation.

Also available is Cressall Resistors’ rang of low noise ES braking resistors, which has recently been expanded with the addition of 1.0 and 2.0kW sized models. These new ratings complement the existing array, which includes 0.6, 1.5, 3.0 and 4.5kW versions with resistance values from 3.9Ω to 330Ω. The new 1.0 and 2.0 kW sizes are used where there is the need to cope with high levels of regenerated energy in a compact space. This includes motor control on elevators, VSD control and use on conveyors, cranes and winches as well as test loads. Like the HP series, these robust IP20 rated units produce negligible audible noise.

Both sets of resistors are manufactured using high grade nickel chrome wire, which means the resistance value changes only negligibly over the temperature range of the element. “This is a significant factor,” explained CP Automation’s director Tony Young, “because a design using lower grade stainless steel could increase in resistance by as much as 50% - resulting in impaired braking.”

Ends: 421 words

Editor’s note: If you want to stay constantly up to date on the latest news from CP Automation, paste the following link into your RSS reader http://cpa-pr.blogspot.com/atom.xml. If you don’t have an RSS reader, I can recommend the following free package Sharp Reader.

For further information contact:
Tony Young, CP Automation
Unit 8, Ashley Industrial Estate, Exmoor Avenue,
Scunthorpe, DN15 8NJ
Telephone: +44 (0)1724 851 515
Fax: +44 (0)1724 851516
www: http://www.cpaltd.net/ and http://www.euroserveltd.net/
e-mail: tony.young@cpaltd.net

Press enquiries: Richard Stone
Stone Junction, 33 Kirkdale,
Sydenham, London, SE26 4BT
Telephone: +44 (0) 20 8699 7743
Fax: +44 (0) 20 8699 7743
e-mail: richards@stonejunction.co.uk
www: http://www.stonejunction.co.uk/

About CP Automation: CP Automation is a specialist in the repair and replacement of automation equipment including electronic boards, PLCs and Ac and DC drives. It was established to provide an independent maintenance service, without exclusive ties to any manufacturer. However, it does have strong relationships with the principal inverter, encoder, resistors and motor manufacturers.

Ref: CPA016/10/08